New Questions in CCNA 200-120 (HSRP, VRRP, NetFlow, SNMP)
The below are mock questions that were about to appear in exam CCNA 200-120.
Updated : 14th October 2013
Download the Latest 200-120 dumps : Click Here
This file requires Visual Cert Exam Suite: Click Here
Download the latest 200-120 dumps in DOCX format :
Chapter 1, Chapter 2, Chapter 3, Chapter 4, Chapter 5, Chapter 6, Chapter 7, Chapter 8, Chapter 9, Chapter 10, Chapter 11, Chapter 12
CCNA EIGRP Simulation
CCNA ACL2 Simulation
Question 1
Which three are the components of SNMP? (Choose three)
A. MIB
B. SNMP Manager
C. SysLog Server
D. SNMP Agent
E. Set
Answer : A, B, D
Question 2
What are the Popular destinations for syslog messages to be saved?
A. Flash
B. The logging buffer .RAM
C. The console terminal
D. Other terminals
E. Syslog server
Answer: B, C, E
Question 3
Syslog was configured with a level 3 trap. Which 3 types of logs would be generated (choose three)
A.Emergencies
B.Alerts
C.Critical
D.Errors
E.Warnings
Answer: A, B, C
Question 4
What are the benefit of using Netflow? (Choose three.)
A. Network, Application & User Monitoring
B. Network Planning
C. Security Analysis
D. Accounting/Billing
Answer: A, C, D
Question 5
Which protocol can cause overload on a CPU of a managed device?
A. Netflow
B. WCCP
C. IP SLA
D. SNMP
Answer: D
Question 6
Which one of these is a valid HSRP Virtual Mac Address?
A. 0000.0C07.AC01
B. 0000.5E00.0110
C. 0007.B400.1203
D. 0000.C007.0201
Answer: A
Question 7
What are the three things that the Netflow uses to consider the traffic to be in a same flow?
A. IP address
B. Interface name
C. Port numbers
D. L3 protocol type
E. MAC address
Answer: A, C, D
Question 8
What is the alert message generated by SNMP agents called ?
A. TRAP
B. INFORM
C. GET
D. SET
Answer: a,b
Question 9
Which three features are added in SNMPv3 over SNMPv2?
A. Message Integrity
B. Compression
C. Authentication
D. Encryption
E. Error Detection
Answer: A, C, D
Question 10
In a GLBP network, who is responsible for the arp request?
A. AVF
B. AVG
C. Active Router
D. Standby Router
Answer: B
Question 11
What levels will be trapped if the administrator executes the command
router(cfg)#logging trap 4
(Choose four.)
A. Emergency
B. Notice
C. Alert
D. Error
E. Warning
Answer: A, C, D, E
Question 12
What are the three things that netflow uses to consider the traffic to be in a same flow?
A. IP address
B. Interface name
C. Port numbers
D. L3 protocol type
Answer: A, C, D
Question 13
Which is true about OSPF router-id? (Choose two .)
A. It is used for type 1 router LSA
B. Highest IP address of the loopback is used
C. router-id needs to be matched on ospf neighbors
D. router-id is 16 bit
Answer : A, B
Question 14
In GLBP, which router will respond to client ARP requests?
A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
B. All GLBP member routers will reply in round-robin fashion.
C. The active virtual gateway will reply with its own hardware MAC address.
D. The GLBP member routers will reply with one of four possible burned in hardware addresses.
Answer: A
Question 15
Which statement describes VRRP object tracking?
A. It monitors traffic flow and link utilization.
B. It ensures the best VRRP router is the virtual router master for the group.
C. It causes traffic to dynamically move to higher bandwidth links
D. It thwarts man-in-the-middle attacks.
Answer: B
Question 16
What are three benefits of GLBP? (Choose three.)
A. GLBP supports up to eight virtual forwarders per GLBP group.
B. GLBP supports clear text and MD5 password authentication between GLBP group members.
C. GLBP is an open source standardized protocol that can be used with multiple vendors.
D. GLBP supports up to 1024 virtual routers.
E. GLBP can load share traffic across a maximum of four routers.
F. GLBP elects two AVGs and two standby AVGs for redundancy.
Answer : B, D, E
Question 17
Which three statements about HSRP operation are true? (Choose three.)
A. The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B. The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C. HSRP supports only clear-text authentication.
D. The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
E. The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
Answer : A, B, F
Question 18
Which three statements about Syslog utilization are true? (Choose three.)
A. Utilizing Syslog improves network performance.
B. The Syslog server automatically notifies the network administrator of network problems.
C. A Syslog server provides the storage space necessary to store log files without using router disk space.
D. There are more Syslog messages available within Cisco IOS than there are comparable SNMP trap messages.
E. Enabling Syslog on a router automatically enables NTP for accurate time stamping.
F. A Syslog server helps in aggregation of logs and alerts.
Answer: C, D, F
Question 19
A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)
A. informational
B. emergency
C. warning
D. critical
E. debug
F. error
Answer: B, D, F
Question 20
What is the default Syslog facility level?
A. local4
B. local5
C. local6
D. local7
Answer: D
Question 21
What command instructs the device to timestamp Syslog debug messages in milliseconds?
A. service timestamps log datetime localtime
B. service timestamps debug datetime msec
C. service timestamps debug datetime localtime
D. service timestamps log datetime msec
Answer: B
Question 22
Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.)
A. SNMPv3 enhanced SNMPv2 security features
B. SNMPv3 added the Inform protocol message to SNMP.
C. SNMPv2 added the Inform protocol message to SNMP.
D. SNMPv3 added the GetBulk protocol messages to SNMP.
E. SNMPv2 added the GetBulk protocol message to SNMP.
F. SNMPv2 added the GetNext protocol message to SNMP.
Answer: A, C, E
Question 23
What are three reasons to collect Netflow data on a company network? (Choose three.)
A. To identify applications causing congestion.
B. To authorize user network access.
C. To report and alert link up / down instances.
D. To diagnose slow network performance, bandwidth hogs, and bandwidth utilization.
E. To detect suboptimal routing in the network.
F. To confirm the appropriate amount of bandwidth that has been allocated to each Class of Service.
Answer: A, D, F
Question 24
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Question 25
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
A. SNMP
B. Netflow
C. WCCP
D. IP SLA
Answer: B
Question 26
What command visualizes the general NetFlow data on the command line?
A. show ip flow export
B. show ip flow top-talkers
C. show ip cache flow
D. show mls sampling
E. show mls netflow ip
Answer: C
Question 27
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop
Answer: A, D, E
Question 28
What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)
A. CPU utilization
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation
Answer: A, B, C
Question 29
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Answer: B, D
Question 30
When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?
A. exstart state > loading state > exchange state > full state
B. exstart state > exchange state > loading state > full state
C. exstart state > full state > loading state > exchange state
D. loading state > exchange state > full state > exstart state
Answer: B
Question 31
What are the Popular destinations for syslog messages to be saved?
A. Flash
B. The logging buffer RAM
C. The console terminal
D. Other terminals
E. Syslog server
Answer: B, C, E
Question 32
What are the benefit of using Netflow? (Choose three.)
A. Network, Application & User Monitoring
B. Network Planning
C. Security Analysis
D. Accounting/Billing
Answer: A, C, D
Updated : 14th October 2013
Download the Latest 200-120 dumps : Click Here
This file requires Visual Cert Exam Suite: Click Here
Download the latest 200-120 dumps in DOCX format :
Chapter 1, Chapter 2, Chapter 3, Chapter 4, Chapter 5, Chapter 6, Chapter 7, Chapter 8, Chapter 9, Chapter 10, Chapter 11, Chapter 12
CCNA EIGRP Simulation
CCNA ACL2 Simulation
Question 1
Which three are the components of SNMP? (Choose three)
A. MIB
B. SNMP Manager
C. SysLog Server
D. SNMP Agent
E. Set
Answer : A, B, D
Question 2
What are the Popular destinations for syslog messages to be saved?
A. Flash
B. The logging buffer .RAM
C. The console terminal
D. Other terminals
E. Syslog server
Answer: B, C, E
Question 3
Syslog was configured with a level 3 trap. Which 3 types of logs would be generated (choose three)
A.Emergencies
B.Alerts
C.Critical
D.Errors
E.Warnings
Answer: A, B, C
Question 4
What are the benefit of using Netflow? (Choose three.)
A. Network, Application & User Monitoring
B. Network Planning
C. Security Analysis
D. Accounting/Billing
Answer: A, C, D
Question 5
Which protocol can cause overload on a CPU of a managed device?
A. Netflow
B. WCCP
C. IP SLA
D. SNMP
Answer: D
Question 6
Which one of these is a valid HSRP Virtual Mac Address?
A. 0000.0C07.AC01
B. 0000.5E00.0110
C. 0007.B400.1203
D. 0000.C007.0201
Answer: A
Question 7
What are the three things that the Netflow uses to consider the traffic to be in a same flow?
A. IP address
B. Interface name
C. Port numbers
D. L3 protocol type
E. MAC address
Answer: A, C, D
Question 8
What is the alert message generated by SNMP agents called ?
A. TRAP
B. INFORM
C. GET
D. SET
Answer: a,b
Question 9
Which three features are added in SNMPv3 over SNMPv2?
A. Message Integrity
B. Compression
C. Authentication
D. Encryption
E. Error Detection
Answer: A, C, D
Question 10
In a GLBP network, who is responsible for the arp request?
A. AVF
B. AVG
C. Active Router
D. Standby Router
Answer: B
Question 11
What levels will be trapped if the administrator executes the command
router(cfg)#logging trap 4
(Choose four.)
A. Emergency
B. Notice
C. Alert
D. Error
E. Warning
Answer: A, C, D, E
Question 12
What are the three things that netflow uses to consider the traffic to be in a same flow?
A. IP address
B. Interface name
C. Port numbers
D. L3 protocol type
Answer: A, C, D
Question 13
Which is true about OSPF router-id? (Choose two .)
A. It is used for type 1 router LSA
B. Highest IP address of the loopback is used
C. router-id needs to be matched on ospf neighbors
D. router-id is 16 bit
Answer : A, B
Question 14
In GLBP, which router will respond to client ARP requests?
A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
B. All GLBP member routers will reply in round-robin fashion.
C. The active virtual gateway will reply with its own hardware MAC address.
D. The GLBP member routers will reply with one of four possible burned in hardware addresses.
Answer: A
Question 15
Which statement describes VRRP object tracking?
A. It monitors traffic flow and link utilization.
B. It ensures the best VRRP router is the virtual router master for the group.
C. It causes traffic to dynamically move to higher bandwidth links
D. It thwarts man-in-the-middle attacks.
Answer: B
Question 16
What are three benefits of GLBP? (Choose three.)
A. GLBP supports up to eight virtual forwarders per GLBP group.
B. GLBP supports clear text and MD5 password authentication between GLBP group members.
C. GLBP is an open source standardized protocol that can be used with multiple vendors.
D. GLBP supports up to 1024 virtual routers.
E. GLBP can load share traffic across a maximum of four routers.
F. GLBP elects two AVGs and two standby AVGs for redundancy.
Answer : B, D, E
Question 17
Which three statements about HSRP operation are true? (Choose three.)
A. The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B. The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C. HSRP supports only clear-text authentication.
D. The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
E. The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
Answer : A, B, F
Question 18
Which three statements about Syslog utilization are true? (Choose three.)
A. Utilizing Syslog improves network performance.
B. The Syslog server automatically notifies the network administrator of network problems.
C. A Syslog server provides the storage space necessary to store log files without using router disk space.
D. There are more Syslog messages available within Cisco IOS than there are comparable SNMP trap messages.
E. Enabling Syslog on a router automatically enables NTP for accurate time stamping.
F. A Syslog server helps in aggregation of logs and alerts.
Answer: C, D, F
Question 19
A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)
A. informational
B. emergency
C. warning
D. critical
E. debug
F. error
Answer: B, D, F
Question 20
What is the default Syslog facility level?
A. local4
B. local5
C. local6
D. local7
Answer: D
Question 21
What command instructs the device to timestamp Syslog debug messages in milliseconds?
A. service timestamps log datetime localtime
B. service timestamps debug datetime msec
C. service timestamps debug datetime localtime
D. service timestamps log datetime msec
Answer: B
Question 22
Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.)
A. SNMPv3 enhanced SNMPv2 security features
B. SNMPv3 added the Inform protocol message to SNMP.
C. SNMPv2 added the Inform protocol message to SNMP.
D. SNMPv3 added the GetBulk protocol messages to SNMP.
E. SNMPv2 added the GetBulk protocol message to SNMP.
F. SNMPv2 added the GetNext protocol message to SNMP.
Answer: A, C, E
Question 23
What are three reasons to collect Netflow data on a company network? (Choose three.)
A. To identify applications causing congestion.
B. To authorize user network access.
C. To report and alert link up / down instances.
D. To diagnose slow network performance, bandwidth hogs, and bandwidth utilization.
E. To detect suboptimal routing in the network.
F. To confirm the appropriate amount of bandwidth that has been allocated to each Class of Service.
Answer: A, D, F
Question 24
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Question 25
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
A. SNMP
B. Netflow
C. WCCP
D. IP SLA
Answer: B
Question 26
What command visualizes the general NetFlow data on the command line?
A. show ip flow export
B. show ip flow top-talkers
C. show ip cache flow
D. show mls sampling
E. show mls netflow ip
Answer: C
Question 27
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop
Answer: A, D, E
Question 28
What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)
A. CPU utilization
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation
Answer: A, B, C
Question 29
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Answer: B, D
Question 30
When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?
A. exstart state > loading state > exchange state > full state
B. exstart state > exchange state > loading state > full state
C. exstart state > full state > loading state > exchange state
D. loading state > exchange state > full state > exstart state
Answer: B
Question 31
What are the Popular destinations for syslog messages to be saved?
A. Flash
B. The logging buffer RAM
C. The console terminal
D. Other terminals
E. Syslog server
Answer: B, C, E
Question 32
What are the benefit of using Netflow? (Choose three.)
A. Network, Application & User Monitoring
B. Network Planning
C. Security Analysis
D. Accounting/Billing
Answer: A, C, D
Good work examtut.com
two were based on the NETFLOW SNMP
one was of the MAC address HSRP
Details Required For CCNA Voucher For Discount Processing:
1-Full Name. 1st Name & Last Name (as you want to appear on certificate & documents)
2-Country.
3-City.
4-State.
5-Pin Code (or Area Code)
6-Residential Address (or where you can collect your Certificate or further correspondence
can be received)
7-Date of birth
Add me on Skype through this information which is written below:
Skype Name: rockon660
you can also email me at this email address which is written below:
madeelqaiser@gmail.com
If you have any Questions feel free to contact me.
Thanks,
Best regards,
Adeel
would you please add the updates
thank you
thank you
please correct it.
thank you
Thank you very much examtut.com
Someone can show me how to get the CCNA 200-120 document for download ?
mail me on yabrebeny@yahoo.fr
Which three statements about HSRP operation are true? (Choose three.)
A. The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B. The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C. HSRP supports only clear-text authentication.
D. The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
E. The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
The righ answers are B, E and F
Source: http://www.cisco.com/en/US/docs/switches/datacenter/sw/5_x/nx-os/unicast/configuration/guide/l3_hsrp.html#wp1509583
Hi I nailed the new CCNA Exam earlier, with a score of 1000/1000
New questions came accross from http://www.examtut.com/2013/09/new-questions-in-ccna-200-120-hsrp-vrrp.html
but encountered 2 NEW QUESION w/c i havent seen on any dumps:
Q1. What is SNMPv2 authentication procol.
A. Community Strings
B. HMAC-MD5
C. HDMAC-SHA
I answered "B" tho. (not xur if my answer is correct)
Q2 (Etherchannel Questions that goes like this)
Refer to the exhibit. Etherchannel has been configured on Switch1 as shown.
Switch1# conf t
Switch1(config)# interface range gigabitethernet 1/1
Switch1(config)# Channel-group 5 Mode "AUTO"
Switch1#
Switch1(config)# interface range gigabitethernet 1/2
Switch1(config)# Channel-group 5 Mode "AUTO"
Which is the correct command set to configure etherchannel on Switch2?
A.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode auto
B.
Switch2# configure terminal
Switch2(config)# interface range gigabitethemet3/1 -2
Switch2(config-if)# channel-group 5 mode passive
C.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode desirable
D.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode ACTIVE
I may not remember the exact wordings of the question,
but it mainly says "AUTO" on the other switch and asked wat mode should be on the other end?
I put D as my answer, the one with an "ACTIVE" word, not xur if its correct.
anyway i hope some 1 can update the NEW CCNA Questions with ANS with this info.
To all NEW CAndidates? BEST OF LUCK!
Thanks 9tut, examtut and Examcollection.
DUMPS are updated.
CHEERS!
~Mack
Q1. What is SNMPv2 authentication procol.
A. Community Strings
B. HMAC-MD5
C. HDMAC-SHA
I think the correct answer is (A) as in the below link
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/sm_snmp.html
(B) & (C) is for SNMPv3
Refer to the exhibit. Etherchannel has been configured on Switch1 as shown.
Switch1# conf t
Switch1(config)# interface range gigabitethernet 1/1
Switch1(config)# Channel-group 5 Mode "AUTO"
Switch1#
Switch1(config)# interface range gigabitethernet 1/2
Switch1(config)# Channel-group 5 Mode "AUTO"
Which is the correct command set to configure etherchannel on Switch2?
A.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode auto
B.
Switch2# configure terminal
Switch2(config)# interface range gigabitethemet3/1 -2
Switch2(config-if)# channel-group 5 mode passive
C.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode desirable
D.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode ACTIVE
Answer is (C)
LACP- can have only ACTIVE or PASSIVE
PAgP- can have only AUTO or DESIRABLE
since we have AUTO in SWA, then SWB should be DESIRABLE
Good Luck to ALL
Thanks to examtut, 9tut, & exam collection.
Simulations:
1. ACL-host B is allowed only web access - different IPs same as Modification 3
2. EIGRP with AS#12
3. ACL - SW can't Ping Router- 3 questions same is in examtut.com
Other questions, is exactly same as the dump (2013-10-12.by.Spintry) on examcollection.com and the above SNMP, Syslog, Netflow
One on Etherchannel:
Network Admin creates a layer 3 Etherchannel, bounding 4 interfaces into channel group 1. On what interface is the IP address configured?
A) the port-channel 1 interface
B) the highest number member interface
C) all member interfaces
D) the lowest number member interface
Answer is A
I also used the dump on examdump.net---was helpful with the Etherchannel questions
Good Luck to all.........
I cleared today ... Thanks examtut......
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli_rel_4_0_1a/sm_snmp.html
snmp v2 uses community strings for an authentication type and snmp v3 has HMAC-MD5 or HMAC-SHA
I will be having exam on the 31st of December 2013.. can anyone tell me how to download the simulations for practice.. or how am I suppose to get it?
you response will be highly appreciated...
GUYS
http://9tut.comxa.com/
is FAKEEEEEEEEEEEEEE
Thanks you examcollection, 9tut, examtut and sprinty
One more thing for egyptian students stay away from New Horizons centers ..it has a very poor service and the test machines sucks ..it keeps disconnecting during the exam ...after finalizing the EIGRP Lap I had to reconfigure it again as it was no submitted:S
3 laps
========
Studied this dumps No new question out of those dumps and espically the new questions because I got about 15 or 20 of them:
http://www.examcollection.com/cisco/Cisco.Test-inside.200-120.v2013-11-04.by.E-Z404.29q.vce.file.html
http://www.examcollection.com/cisco/Cisco.Actualtests.200-120.v2013-10-01.by.examtut.278q.vce.file.html
Or
http://www.examcollection.com/cisco/Cisco.Actualtests.200-120.v2013-10-12.by.Spintry.299q.vce.file.html
Have a look on examtut as well:
http://www.examtut.com/2013/09/new-questions-in-ccna-200-120-hsrp-vrrp.html
ACL 1
http://www.examtut.com/2013/09/access-control-list-acl-simlet.html
ACL 2 ( Modification 4 but for host C not d)
http://www.examtut.com/2013/08/ccna-access-list-control-acl-simulation.html
access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80
access-list 100 deny ip any host 172.22.242.23
access-list 100 permit ip any any
EIGRP but AS 12 or 212
They added an irrelvant network on the main Router I think 192.168.52.0
No passive interfaces is already added this time from their side.
IP default network and ip route are added as well.
simply correct the AS number on the new router and add it on the main one.
Questions that are still in my mind:
https://drive.google.com/file/d/0B5a0xdDRJqewUVhWRlBsMTNSQzQ/edit?usp=sharing
Simlet are ACL, ALC 2, EIGRP.
Study material: www.9tut.com everything on 200-120, http://www.examtut.com/2013/09/new-questions-in-ccna-200-120-hsrp-vrrp.html for new question, http://www.examcollection.com/cisco/Cisco.Actualtests.200-120.v2013-10-01.by.examtut.278q.vce.file.html for valid dumps
Q4 and Q32
Anyone can help to check the correct answer.
http://www.cisco.com/en/US/products/ps6601/products_ios_protocol_group_home.html
"Denial of Service monitoring capabilities, and network monitoring."
Thank so much
thanks examcollection, 9tut, examtut and spintry
I got 3 sims
ACL 1 , 2 & EIGRP
two new questions
One on Etherchannel:
Network Admin creates a layer 3 Etherchannel, bounding 4 interfaces into channel group 1. On what interface is the IP address configured?
A) the port-channel 1 interface
B) the highest number member interface
C) all member interfaces
D) the lowest number member interface
Answer is A
one for For the SNMP :
Q1. What is SNMPv2 authentication procol.
A. Community Strings
B. HMAC-MD5
C. HDMAC-SHA
the answer is B
Authentication Method: Community String
Authentication Protocol: MD5
Here report that the metod is Community Strign for V2 and MD5 for V3
i don't know
Which are the valid dumps?
Which are the valid labs?
I have passed ICND2 (200-100) 973/1000..
CBT Nuggets, Todd Lammle's book , real practice on hardware and of course examtut , and dumps from http://www.examcollection.com/ especially one by RonBoot, helped
and have also
Cisco.Actualtests.200-120.CCNA.v2013-10-01.by.examtut.278q
Although this last dump was for 200-120 , but also helped.
only one question from new topic in which I have to select the virtual mac of HSRP
Two simlets one is in all dumps. In one simlet , which I have never seen anywhere, four questions were asked .there were 5/6 routers running eigrp but all were running same eigrp AS no. and so there was not a single question rather answer about it. One question was about connectivity issue and it was because one of the loopback interface was shutdown , but it was advertise by EIGRP while in other question one of the network was not advertises and in one question problem in forming the neighbour relationship and it was because of passive interface.
Key is to always read the all the answers first , it will save the time which is wasted to look all the config
Most of the dumps with date after 20 Nov are valid { most of them are same anyways}
I have passed ICND2 (200-100) 1000/1000.
CBT Nuggets, Chris Bryant , lead2pass dumps (660 approx. questions of old course) and new questions mentioned all here (Including the 2 etherchannel and 1 snmp question in posts below) all helped me getting the score. Labs and simlets same as mentioned here on examtut.com (except as number or ip addresses might be different).
Clear your concepts
prepare:
dumps (as told above),
labs ,simlets on this website and your good to go.
Regarding the test in my case 95% of the questions were from the examsdeal Website too. A few questions were from the Examtut-Website (look to the “new questions”). Sims as mentioned above Frame relay and EIGRP. EIGRP you can solve with the show ip route and show run command.
Good luck
Biene
got 53, 3 labs.
u will need, ronboots 100q, and the 29 new questions from test-inside.
new questions are also on examsdeal 267
2 of the labs were the showcommand labs from ronboots, the third was a 6 route eigrp lab i never see before, but u dont have to worry, its supereasy and if u fail, it dont matter, cause u can reach the needed points with the the vce files i named above
Q4 and Q32
answer: A B D
Question 8
What is the alert message generated by SNMP agents called ?
A. TRAP
B. INFORM
C. GET
D. SET
Answer: a,b
Question 16
What are three benefits of GLBP? (Choose three.)
A. GLBP supports up to eight virtual forwarders per GLBP group.
B. GLBP supports clear text and MD5 password authentication between GLBP group members.
C. GLBP is an open source standardized protocol that can be used with multiple vendors.
D. GLBP supports up to 1024 virtual routers.
E. GLBP can load share traffic across a maximum of four routers.
F. GLBP elects two AVGs and two standby AVGs for redundancy.
Answer : B, D, E
Question 20
What is the default Syslog facility level?
A. local4
B. local5
C. local6
D. local7
Answer: D
Question 24
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Question 28
What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)
A. CPU utilization
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation
Answer: A, B, C
Question 29
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Refer to the exhibit. Etherchannel has been configured on Switch1 as shown.
Switch1# conf t
Switch1(config)# interface range gigabitethernet 1/1
Switch1(config)# Channel-group 5 Mode "AUTO"
Switch1#
Switch1(config)# interface range gigabitethernet 1/2
Switch1(config)# Channel-group 5 Mode "AUTO"
Which is the correct command set to configure etherchannel on Switch2?
A.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode auto
B.
Switch2# configure terminal
Switch2(config)# interface range gigabitethemet3/1 -2
Switch2(config-if)# channel-group 5 mode passive
C.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode desirable
D.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode ACTIVE
Your comment it's about 200-120 or 200-101?
What new dump you know were is correct?
what kind of the new question is different? Please tell more us. Thank's!
Details Required For CCNA Voucher For Discount Processing:
1-Full Name. 1st Name & Last Name (as you want to appear on certificate & documents)
2-Country.
3-City.
4-State.
5-Pin Code (or Area Code)
6-Residential Address (or where you can collect your Certificate or further correspondence
can be received)
7-Date of birth
Add me on Skype through this information which is written below:
Skype Name: rockon660
you can also email me at this email address which is written below:
madeelqaiser@gmail.com
If you have any Questions feel free to contact me.
Thanks,
Best regards,
Adeel
I got 986/1000.
two new Qs :
1 . Benefits of OSPF ....
2. Syslog msg ...
ACL1,ACL2,EIGRP Labs....